Home › 7/16-20 UNF
7/16-20 UNF — Full Fastener Spec
ASME B1.1 (Unified) · Unf series · Tap drill, clearance hole, torque, strength and tool sizes — every number on one page.
Tap drill (75% thread)
25/64 (0.3906")
9.9 mm · Clearance hole (normal fit): 0.4690" (15/32) ·
Grade 5 torque: 55.2 lb-ft dry
Thread dimensions
Major diameter
0.4375 "
Threads per inch
20
Pitch
1.27 mm
Pitch diameter
0.405 "
Minor diameter
0.3834 "
Tensile stress area
0.11872 in²
Tap drill sizes for 7/16-20 UNF
Percent of thread is a trade-off: 75% is the shop default because the last 25% of engagement adds only a few percent of strength while roughly doubling tapping torque. Drop to 50–65% in tough or gummy material, or for blind holes where a snapped tap means scrapping the part.
| Thread engagement | Exact | Inch drill | Nearest metric drill |
|---|---|---|---|
| 50% | 0.4050" | Y (0.4040") | 10.3 mm |
| 65% | 0.3953" | X (0.3970") | 10 mm |
| 75% | 0.3888" | 25/64 (0.3906") | 9.9 mm |
| 85% | 0.3823" | W (0.3860") | 9.7 mm |
Roll (form) taps need a larger hole than cut taps — add roughly
0.4× the pitch to the 75% cut-tap drill and confirm against your tap maker's chart.
Clearance hole for 7/16-20 UNF
| Fit | Drill | Use |
|---|---|---|
| Close | 0.4530" (29/64) | Located joints, dowel-like alignment |
| Normal | 0.4690" (15/32) | General assembly — use this unless you have a reason not to |
| Loose | 0.4840" (31/64) | Weldments, sheet stacks, tolerance build-up |
7/16-20 UNF torque specs
Calculated with the short-form equation T = K · D · F, using K = 0.2 (plain, dry, as-received steel) and a target clamp load of 75% of proof load — the standard preload target for a reusable joint.
| Grade | Dry | Lubricated | Dry (N·m) | Clamp load |
|---|---|---|---|---|
| Grade 2 Low/medium carbon steel, unmarked head | 35.7 lb-ft | 26.8 lb-ft | 48.4 N·m | 4,897 lb |
| Grade 5 Medium carbon Q&T, 3 radial head marks | 55.2 lb-ft | 41.4 lb-ft | 74.8 N·m | 7,568 lb |
| Grade 8 Medium carbon alloy Q&T, 6 radial head marks | 77.9 lb-ft | 58.4 lb-ft | 106 N·m | 10,684 lb |
| 18-8 SS 304/18-8 stainless | 26 lb-ft | 19.5 lb-ft | 35.2 N·m | 3,561 lb |
The nut factor K dominates this result. Zinc-plated, waxed, anti-seize
and lubricated threads all shift K between roughly 0.10 and 0.25, which is a 2.5×
spread in torque for identical preload. If preload actually matters, torque-to-yield,
angle control or a load-indicating washer beats a torque wrench every time.
Tool sizes
Hex head wrench
5/8"
Hex key (socket head)
3/8