Home › 5/8-11 UNC
5/8-11 UNC — Full Fastener Spec
ASME B1.1 (Unified) · Unc series · Tap drill, clearance hole, torque, strength and tool sizes — every number on one page.
Tap drill (75% thread)
17/32 (0.5312")
13.6 mm · Clearance hole (normal fit): 0.6880" (11/16) ·
Grade 5 torque: 150 lb-ft dry
Thread dimensions
Major diameter
0.625 "
Threads per inch
11
Pitch
2.309 mm
Pitch diameter
0.566 "
Minor diameter
0.5266 "
Tensile stress area
0.226 in²
Tap drill sizes for 5/8-11 UNC
Percent of thread is a trade-off: 75% is the shop default because the last 25% of engagement adds only a few percent of strength while roughly doubling tapping torque. Drop to 50–65% in tough or gummy material, or for blind holes where a snapped tap means scrapping the part.
| Thread engagement | Exact | Inch drill | Nearest metric drill |
|---|---|---|---|
| 50% | 0.5660" | 9/16 (0.5625") | 14.4 mm |
| 65% | 0.5482" | 35/64 (0.5469") | 13.9 mm |
| 75% | 0.5364" | 17/32 (0.5312") | 13.6 mm |
| 85% | 0.5246" | 17/32 (0.5312") | 13.3 mm |
Roll (form) taps need a larger hole than cut taps — add roughly
0.4× the pitch to the 75% cut-tap drill and confirm against your tap maker's chart.
Clearance hole for 5/8-11 UNC
| Fit | Drill | Use |
|---|---|---|
| Close | 0.6560" (21/32) | Located joints, dowel-like alignment |
| Normal | 0.6880" (11/16) | General assembly — use this unless you have a reason not to |
| Loose | 0.7340" (47/64) | Weldments, sheet stacks, tolerance build-up |
5/8-11 UNC torque specs
Calculated with the short-form equation T = K · D · F, using K = 0.2 (plain, dry, as-received steel) and a target clamp load of 75% of proof load — the standard preload target for a reusable joint.
| Grade | Dry | Lubricated | Dry (N·m) | Clamp load |
|---|---|---|---|---|
| Grade 2 Low/medium carbon steel, unmarked head | 97.1 lb-ft | 72.8 lb-ft | 132 N·m | 9,322 lb |
| Grade 5 Medium carbon Q&T, 3 radial head marks | 150 lb-ft | 113 lb-ft | 203 N·m | 14,407 lb |
| Grade 8 Medium carbon alloy Q&T, 6 radial head marks | 212 lb-ft | 159 lb-ft | 287 N·m | 20,340 lb |
| 18-8 SS 304/18-8 stainless | 70.6 lb-ft | 53 lb-ft | 95.8 N·m | 6,780 lb |
The nut factor K dominates this result. Zinc-plated, waxed, anti-seize
and lubricated threads all shift K between roughly 0.10 and 0.25, which is a 2.5×
spread in torque for identical preload. If preload actually matters, torque-to-yield,
angle control or a load-indicating washer beats a torque wrench every time.
Tool sizes
Hex head wrench
15/16"
Hex key (socket head)
1/2