Home › #1-72 UNF
#1-72 UNF — Full Fastener Spec
ASME B1.1 (Unified) · Unf series · Tap drill, clearance hole, torque, strength and tool sizes — every number on one page.
Tap drill (75% thread)
#53 (0.0595")
1.5 mm · Clearance hole (normal fit): 0.0890" (#43) ·
Grade 5 torque: 0.215 lb-ft dry
Thread dimensions
Major diameter
0.073 "
Threads per inch
72
Pitch
0.353 mm
Pitch diameter
0.064 "
Minor diameter
0.058 "
Tensile stress area
0.00278 in²
Tap drill sizes for #1-72 UNF
Percent of thread is a trade-off: 75% is the shop default because the last 25% of engagement adds only a few percent of strength while roughly doubling tapping torque. Drop to 50–65% in tough or gummy material, or for blind holes where a snapped tap means scrapping the part.
| Thread engagement | Exact | Inch drill | Nearest metric drill |
|---|---|---|---|
| 50% | 0.0640" | #52 (0.0635") | 1.6 mm |
| 65% | 0.0613" | 1/16 (0.0625") | 1.6 mm |
| 75% | 0.0595" | #53 (0.0595") | 1.5 mm |
| 85% | 0.0577" | #53 (0.0595") | 1.5 mm |
Roll (form) taps need a larger hole than cut taps — add roughly
0.4× the pitch to the 75% cut-tap drill and confirm against your tap maker's chart.
Clearance hole for #1-72 UNF
| Fit | Drill | Use |
|---|---|---|
| Close | 0.0810" (#46) | Located joints, dowel-like alignment |
| Normal | 0.0890" (#43) | General assembly — use this unless you have a reason not to |
| Loose | 0.1040" (#37) | Weldments, sheet stacks, tolerance build-up |
#1-72 UNF torque specs
Calculated with the short-form equation T = K · D · F, using K = 0.2 (plain, dry, as-received steel) and a target clamp load of 75% of proof load — the standard preload target for a reusable joint.
| Grade | Dry | Lubricated | Dry (N·m) | Clamp load |
|---|---|---|---|---|
| Grade 2 Low/medium carbon steel, unmarked head | 0.139 lb-ft | 0.104 lb-ft | 0.189 N·m | 114 lb |
| Grade 5 Medium carbon Q&T, 3 radial head marks | 0.215 lb-ft | 0.162 lb-ft | 0.292 N·m | 177 lb |
| Grade 8 Medium carbon alloy Q&T, 6 radial head marks | 0.304 lb-ft | 0.228 lb-ft | 0.412 N·m | 249 lb |
| 18-8 SS 304/18-8 stainless | 0.101 lb-ft | 0.076 lb-ft | 0.138 N·m | 83 lb |
The nut factor K dominates this result. Zinc-plated, waxed, anti-seize
and lubricated threads all shift K between roughly 0.10 and 0.25, which is a 2.5×
spread in torque for identical preload. If preload actually matters, torque-to-yield,
angle control or a load-indicating washer beats a torque wrench every time.
Tool sizes
Hex head wrench
5/32"
Hex key (socket head)
1/16