Home › M48×5
M48×5 — Full Fastener Spec
ISO 68-1 / ISO 261 · Coarse series · Tap drill, clearance hole, torque, strength and tool sizes — every number on one page.
Tap drill (75% thread)
43 mm
Nearest inch drill: 27/16 (1.6875") · Clearance hole (normal fit): 52 mm ·
8.8 torque: 6152 N·m dry
Thread dimensions
Major diameter
48 mm
Pitch
5 mm
TPI (equivalent)
5.08
Pitch diameter
44.752 mm
Minor diameter
42.587 mm
Tensile stress area
1473.15 mm²
Tap drill sizes for M48×5
Percent of thread is a trade-off: 75% is the shop default because the last 25% of engagement adds only a few percent of strength while roughly doubling tapping torque. Drop to 50–65% in tough or gummy material, or for blind holes where a snapped tap means scrapping the part.
| Thread engagement | Exact | Metric drill | Nearest inch drill |
|---|---|---|---|
| 50% | 44.752 mm | 45 mm | 1.7656" (113/64 drill) |
| 65% | 43.778 mm | 44 mm | 1.7344" (111/64 drill) |
| 75% | 43.129 mm | 43 mm | 1.6875" (27/16 drill) |
| 85% | 42.479 mm | 42.5 mm | 1.6719" (107/64 drill) |
Roll (form) taps need a larger hole than cut taps — add roughly
0.4× the pitch to the 75% cut-tap drill and confirm against your tap maker's chart.
Clearance hole for M48×5
| Fit | Hole | Use |
|---|---|---|
| Close | 50 mm | Located joints, dowel-like alignment |
| Normal | 52 mm | General assembly — use this unless you have a reason not to |
| Loose | 56 mm | Weldments, sheet stacks, tolerance build-up |
M48×5 torque specs
Calculated with the short-form equation T = K · D · F, using K = 0.2 (plain, dry, as-received steel) and a target clamp load of 75% of proof load — the standard preload target for a reusable joint.
| Grade | Dry | Lubricated | Dry (lb-ft) | Clamp load |
|---|---|---|---|---|
| 4.6 Low-carbon steel, general purpose | 2387 N·m | 1790 N·m | 1760 lb-ft | 248.6 kN |
| 8.8 Medium-carbon, quenched & tempered — the default structural grade | 6152 N·m | 4614 N·m | 4537 lb-ft | 640.8 kN |
| 10.9 Alloy steel, Q&T — high strength | 8804 N·m | 6603 N·m | 6493 lb-ft | 917 kN |
| 12.9 Alloy steel, Q&T — highest common grade (socket head cap screws) | 10288 N·m | 7716 N·m | 7588 lb-ft | 1071.7 kN |
| A2-70 304 stainless, cold worked | 4773 N·m | 3580 N·m | 3520 lb-ft | 497.2 kN |
The nut factor K dominates this result. Zinc-plated, waxed, anti-seize
and lubricated threads all shift K between roughly 0.10 and 0.25, which is a 2.5×
spread in torque for identical preload. If preload actually matters, torque-to-yield,
angle control or a load-indicating washer beats a torque wrench every time.
Tool sizes
Hex head wrench
75 mm
Hex key (socket head)
36 mm