What is the tap drill size for G 1/8?

8.80 mm, which gives 80% thread engagement. Published figures for BSPP sizes vary because each table silently assumes a different engagement, anywhere from about 71% to 88%. The minor diameter is 8.566 mm.

What is the actual diameter of a G 1/8 thread?

G 1/8 has a major diameter of 9.728 mm (0.3830 in), not 1/8 inch. G sizes are named by nominal bore, not by measured diameter.

Does G 1/8 seal on the thread?

No. BSPP is a parallel thread and cannot seal by thread interference. It needs a bonded seal, an O-ring or a cone seat.

Home › Pipe threads › G 1/8

G 1/8 (BSPP) Thread Dimensions

ISO 228-1 · 55° Whitworth form · parallel, not tapered · 28 TPI

Tap drill (80% engagement) 8.80 mm Major 9.728 mm · pitch dia 9.147 mm · minor 8.566 mm

G 1/8 does not measure 1/8″. It measures 9.728 mm (0.3830″) across the crests. Like every pipe thread, the G number is a nominal bore inherited from wrought iron pipe, not a diameter you can put a caliper on.

Dimensions

Major diameter (d)

9.728 mm

Pitch diameter (d₂)

9.147 mm

Minor diameter (d₁)

8.566 mm

Threads per inch

Pitch

0.907 mm

Thread height (h)

0.581 mm

Crest / root radius

0.125 mm

Thread angle

55°

ISO 228-1 tabulates only the major diameter. Pitch and minor diameters follow from the basic profile — h = 0.640327 × p, d₂ = d − h, d₁ = d − 2h — which is how the figures above were produced.

Why sources disagree about the G 1/8 tap drill

Look this drill size up in three places and you will get three answers. They are not typos. Every table silently picks a different thread engagement — how much of the theoretical thread form the tap actually cuts — and then prints the resulting number without saying which one it chose. Across published BSPP tables the implied engagement ranges from about 71% to about 88%.

So here is every drill you can actually buy for this size, and what each one really gives you:

Drill	Thread engagement
8.60 mm	97%	Maximum strength, highest tapping torque
8.70 mm	88%	Strong thread, still taps comfortably
8.80 mm	80%	Common commercial choice ← recommended
8.90 mm	71%	Easiest tapping, weakest thread

8.80 mm is the one to use unless you have a reason not to. Going nearer the minor diameter (8.566 mm) buys thread strength at the cost of tapping torque and tap breakage — and on a parallel pipe thread that trade is rarely worth making, because the thread is not what seals the joint.

BSPP does not seal on the thread. The flanks are parallel, so tightening only pulls metal against metal and never wedges. The seal has to come from somewhere else: a bonded seal (Dowty washer) under the hex, an O-ring in a face groove per ISO 1179-2, or a 60° cone seat. PTFE tape on a BSPP thread accomplishes nothing except making the joint harder to undo.

G 1/8 against the taper threads

G 1/8 shares its 55° Whitworth form and its 28 TPI with 1/8″ BSPT (R1/8 / Rc1/8), which is why the two get mixed up constantly. The difference is that BSPT is tapered and BSPP is not. A BSPP male will start into a BSPT female and feel fine for a couple of turns, then either jam or never tighten.

The one pairing that is standard: ISO 7-1 allows a taper male (R) into a parallel female (Rp). Rp and G have the identical basic profile and differ only in tolerance class, which is the source of most of the surviving confusion in catalogues.

BSPP vs BSPT → Full BSPP chart → 1/8″ BSPT → All pipe threads →