Home › 5/16-18 UNC
5/16-18 UNC — Full Fastener Spec
ASME B1.1 (Unified) · Unc series · Tap drill, clearance hole, torque, strength and tool sizes — every number on one page.
Tap drill (75% thread)
F (0.2570")
6.6 mm · Clearance hole (normal fit): 0.3440" (11/32) ·
Grade 5 torque: 17.4 lb-ft dry
Thread dimensions
Major diameter
0.3125 "
Threads per inch
18
Pitch
1.411 mm
Pitch diameter
0.2764 "
Minor diameter
0.2524 "
Tensile stress area
0.05243 in²
Tap drill sizes for 5/16-18 UNC
Percent of thread is a trade-off: 75% is the shop default because the last 25% of engagement adds only a few percent of strength while roughly doubling tapping torque. Drop to 50–65% in tough or gummy material, or for blind holes where a snapped tap means scrapping the part.
| Thread engagement | Exact | Inch drill | Nearest metric drill |
|---|---|---|---|
| 50% | 0.2764" | J (0.2770") | 7 mm |
| 65% | 0.2656" | 17/64 (0.2656") | 6.7 mm |
| 75% | 0.2584" | F (0.2570") | 6.6 mm |
| 85% | 0.2512" | E (0.2500") | 6.4 mm |
Roll (form) taps need a larger hole than cut taps — add roughly
0.4× the pitch to the 75% cut-tap drill and confirm against your tap maker's chart.
Clearance hole for 5/16-18 UNC
| Fit | Drill | Use |
|---|---|---|
| Close | 0.3280" (21/64) | Located joints, dowel-like alignment |
| Normal | 0.3440" (11/32) | General assembly — use this unless you have a reason not to |
| Loose | 0.3590" (23/64) | Weldments, sheet stacks, tolerance build-up |
5/16-18 UNC torque specs
Calculated with the short-form equation T = K · D · F, using K = 0.2 (plain, dry, as-received steel) and a target clamp load of 75% of proof load — the standard preload target for a reusable joint.
| Grade | Dry | Lubricated | Dry (N·m) | Clamp load |
|---|---|---|---|---|
| Grade 2 Low/medium carbon steel, unmarked head | 11.3 lb-ft | 8.45 lb-ft | 15.3 N·m | 2,162 lb |
| Grade 5 Medium carbon Q&T, 3 radial head marks | 17.4 lb-ft | 13.1 lb-ft | 23.6 N·m | 3,342 lb |
| Grade 8 Medium carbon alloy Q&T, 6 radial head marks | 24.6 lb-ft | 18.4 lb-ft | 33.3 N·m | 4,718 lb |
| 18-8 SS 304/18-8 stainless | 8.19 lb-ft | 6.14 lb-ft | 11.1 N·m | 1,572 lb |
The nut factor K dominates this result. Zinc-plated, waxed, anti-seize
and lubricated threads all shift K between roughly 0.10 and 0.25, which is a 2.5×
spread in torque for identical preload. If preload actually matters, torque-to-yield,
angle control or a load-indicating washer beats a torque wrench every time.
Tool sizes
Hex head wrench
1/2"
Hex key (socket head)
1/4