Home › #4-48 UNF
#4-48 UNF — Full Fastener Spec
ASME B1.1 (Unified) · Unf series · Tap drill, clearance hole, torque, strength and tool sizes — every number on one page.
Tap drill (75% thread)
#42 (0.0935")
2.3 mm · Clearance hole (normal fit): 0.1280" (#30) ·
Grade 5 torque: 0.786 lb-ft dry
Thread dimensions
Major diameter
0.112 "
Threads per inch
48
Pitch
0.529 mm
Pitch diameter
0.0985 "
Minor diameter
0.0894 "
Tensile stress area
0.0066 in²
Tap drill sizes for #4-48 UNF
Percent of thread is a trade-off: 75% is the shop default because the last 25% of engagement adds only a few percent of strength while roughly doubling tapping torque. Drop to 50–65% in tough or gummy material, or for blind holes where a snapped tap means scrapping the part.
| Thread engagement | Exact | Inch drill | Nearest metric drill |
|---|---|---|---|
| 50% | 0.0985" | #40 (0.0980") | 2.5 mm |
| 65% | 0.0944" | 3/32 (0.0938") | 2.4 mm |
| 75% | 0.0917" | #42 (0.0935") | 2.3 mm |
| 85% | 0.0890" | #43 (0.0890") | 2.3 mm |
Roll (form) taps need a larger hole than cut taps — add roughly
0.4× the pitch to the 75% cut-tap drill and confirm against your tap maker's chart.
Clearance hole for #4-48 UNF
| Fit | Drill | Use |
|---|---|---|
| Close | 0.1200" (#31) | Located joints, dowel-like alignment |
| Normal | 0.1280" (#30) | General assembly — use this unless you have a reason not to |
| Loose | 0.1440" (#27) | Weldments, sheet stacks, tolerance build-up |
#4-48 UNF torque specs
Calculated with the short-form equation T = K · D · F, using K = 0.2 (plain, dry, as-received steel) and a target clamp load of 75% of proof load — the standard preload target for a reusable joint.
| Grade | Dry | Lubricated | Dry (N·m) | Clamp load |
|---|---|---|---|---|
| Grade 2 Low/medium carbon steel, unmarked head | 0.509 lb-ft | 0.381 lb-ft | 0.69 N·m | 272 lb |
| Grade 5 Medium carbon Q&T, 3 radial head marks | 0.786 lb-ft | 0.59 lb-ft | 1.07 N·m | 421 lb |
| Grade 8 Medium carbon alloy Q&T, 6 radial head marks | 1.11 lb-ft | 0.832 lb-ft | 1.5 N·m | 594 lb |
| 18-8 SS 304/18-8 stainless | 0.37 lb-ft | 0.277 lb-ft | 0.501 N·m | 198 lb |
The nut factor K dominates this result. Zinc-plated, waxed, anti-seize
and lubricated threads all shift K between roughly 0.10 and 0.25, which is a 2.5×
spread in torque for identical preload. If preload actually matters, torque-to-yield,
angle control or a load-indicating washer beats a torque wrench every time.
Tool sizes
Hex head wrench
1/4"
Hex key (socket head)
3/32