Home › 1/4-20 UNC
1/4-20 UNC — Full Fastener Spec
ASME B1.1 (Unified) · Unc series · Tap drill, clearance hole, torque, strength and tool sizes — every number on one page.
Tap drill (75% thread)
#7 (0.2010")
5.1 mm · Clearance hole (normal fit): 0.2810" (9/32) ·
Grade 5 torque: 8.45 lb-ft dry
Thread dimensions
Major diameter
0.25 "
Threads per inch
20
Pitch
1.27 mm
Pitch diameter
0.2175 "
Minor diameter
0.1959 "
Tensile stress area
0.03182 in²
Tap drill sizes for 1/4-20 UNC
Percent of thread is a trade-off: 75% is the shop default because the last 25% of engagement adds only a few percent of strength while roughly doubling tapping torque. Drop to 50–65% in tough or gummy material, or for blind holes where a snapped tap means scrapping the part.
| Thread engagement | Exact | Inch drill | Nearest metric drill |
|---|---|---|---|
| 50% | 0.2175" | 7/32 (0.2188") | 5.5 mm |
| 65% | 0.2078" | #4 (0.2090") | 5.3 mm |
| 75% | 0.2013" | #7 (0.2010") | 5.1 mm |
| 85% | 0.1948" | #9 (0.1960") | 4.9 mm |
Roll (form) taps need a larger hole than cut taps — add roughly
0.4× the pitch to the 75% cut-tap drill and confirm against your tap maker's chart.
Clearance hole for 1/4-20 UNC
| Fit | Drill | Use |
|---|---|---|
| Close | 0.2660" (17/64) | Located joints, dowel-like alignment |
| Normal | 0.2810" (9/32) | General assembly — use this unless you have a reason not to |
| Loose | 0.2970" (19/64) | Weldments, sheet stacks, tolerance build-up |
1/4-20 UNC torque specs
Calculated with the short-form equation T = K · D · F, using K = 0.2 (plain, dry, as-received steel) and a target clamp load of 75% of proof load — the standard preload target for a reusable joint.
| Grade | Dry | Lubricated | Dry (N·m) | Clamp load |
|---|---|---|---|---|
| Grade 2 Low/medium carbon steel, unmarked head | 5.47 lb-ft | 4.1 lb-ft | 7.42 N·m | 1,312 lb |
| Grade 5 Medium carbon Q&T, 3 radial head marks | 8.45 lb-ft | 6.34 lb-ft | 11.5 N·m | 2,028 lb |
| Grade 8 Medium carbon alloy Q&T, 6 radial head marks | 11.9 lb-ft | 8.95 lb-ft | 16.2 N·m | 2,863 lb |
| 18-8 SS 304/18-8 stainless | 3.98 lb-ft | 2.98 lb-ft | 5.39 N·m | 954 lb |
The nut factor K dominates this result. Zinc-plated, waxed, anti-seize
and lubricated threads all shift K between roughly 0.10 and 0.25, which is a 2.5×
spread in torque for identical preload. If preload actually matters, torque-to-yield,
angle control or a load-indicating washer beats a torque wrench every time.
Tool sizes
Hex head wrench
7/16"
Hex key (socket head)
3/16