Home › #0-80 UNF
#0-80 UNF — Full Fastener Spec
ASME B1.1 (Unified) · Unf series · Tap drill, clearance hole, torque, strength and tool sizes — every number on one page.
Tap drill (75% thread)
3/64 (0.0469")
1.2 mm · Clearance hole (normal fit): 0.0760" (#48) ·
Grade 5 torque: 0.115 lb-ft dry
Thread dimensions
Major diameter
0.06 "
Threads per inch
80
Pitch
0.318 mm
Pitch diameter
0.0519 "
Minor diameter
0.0465 "
Tensile stress area
0.0018 in²
Tap drill sizes for #0-80 UNF
Percent of thread is a trade-off: 75% is the shop default because the last 25% of engagement adds only a few percent of strength while roughly doubling tapping torque. Drop to 50–65% in tough or gummy material, or for blind holes where a snapped tap means scrapping the part.
| Thread engagement | Exact | Inch drill | Nearest metric drill |
|---|---|---|---|
| 50% | 0.0519" | #55 (0.0520") | 1.3 mm |
| 65% | 0.0494" | #55 (0.0520") | 1.3 mm |
| 75% | 0.0478" | 3/64 (0.0469") | 1.2 mm |
| 85% | 0.0462" | #56 (0.0465") | 1.2 mm |
Roll (form) taps need a larger hole than cut taps — add roughly
0.4× the pitch to the 75% cut-tap drill and confirm against your tap maker's chart.
Clearance hole for #0-80 UNF
| Fit | Drill | Use |
|---|---|---|
| Close | 0.0670" (#51) | Located joints, dowel-like alignment |
| Normal | 0.0760" (#48) | General assembly — use this unless you have a reason not to |
| Loose | 0.0940" (3/32) | Weldments, sheet stacks, tolerance build-up |
#0-80 UNF torque specs
Calculated with the short-form equation T = K · D · F, using K = 0.2 (plain, dry, as-received steel) and a target clamp load of 75% of proof load — the standard preload target for a reusable joint.
| Grade | Dry | Lubricated | Dry (N·m) | Clamp load |
|---|---|---|---|---|
| Grade 2 Low/medium carbon steel, unmarked head | 0.074 lb-ft | 0.056 lb-ft | 0.101 N·m | 74 lb |
| Grade 5 Medium carbon Q&T, 3 radial head marks | 0.115 lb-ft | 0.086 lb-ft | 0.155 N·m | 114 lb |
| Grade 8 Medium carbon alloy Q&T, 6 radial head marks | 0.162 lb-ft | 0.121 lb-ft | 0.219 N·m | 161 lb |
| 18-8 SS 304/18-8 stainless | 0.054 lb-ft | 0.04 lb-ft | 0.073 N·m | 53 lb |
The nut factor K dominates this result. Zinc-plated, waxed, anti-seize
and lubricated threads all shift K between roughly 0.10 and 0.25, which is a 2.5×
spread in torque for identical preload. If preload actually matters, torque-to-yield,
angle control or a load-indicating washer beats a torque wrench every time.
Tool sizes
Hex head wrench
5/32"
Hex key (socket head)
0.050"